Skip to content

Cl2/Ar and Cl2/O2 Inductively Coupled Plasma Etching of (-201) β-Ga2O3

Document Type
Publications · Journal Article
Registered DB
KCISCIEScopus
Journal Ranking
JCR Q3Scopus Q2KCI Q4
Journal
Electronic Materials Letters22(1) · pp.8 · 2026
Citation
Web of Science 0Scopus 0KCI 0
FWCI (Scopus)
0
JCR IF
JCR 2024 2.6
ISSN
1738-8090

Authors

  1. Choi, Byoung SuFirst authorPusan Natl Univ, Dept Nano Fus Technol, Miryang 50463, Gyeongnam, South Korea
  2. CHAE, KIHUNPusan Natl Univ, Dept Nanomechatron Engn, Busan 46241, South Korea
  3. Hwang, SunguPusan Natl Univ, Dept Nanomechatron Engn, Busan 46241, South Korea
  4. Kim, Jin KonPusan Natl Univ, Dept Nanomechatron Engn, Busan 46241, South Korea
  5. Lee, Byeong WooKorea Maritime & Ocean Univ, Dept Ocean Adv Mat Convergence Engn, Busan 49112, South Korea
  6. Ryu, Jeong HoKorea Natl Univ Transportat, Dept Mat Sci & Engn, Chungju 27469, Chungbuk, South Korea
  7. Pearton, Stephen J.Univ Florida, Dept Mat Sci & Engn, Gainesville, FL 32611 USA
  8. Cho, HyunCorresponding authorPusan Natl Univ, Dept Nanomechatron Engn, Busan 46241, South Korea

Abstract

A comparative study of Cl-2/Ar and Cl-2/O-2 inductively coupled plasma etching of (-201) beta-Ga2O3 was performed, and the effect of additive gases on the etch characteristics was studied. In both plasma chemistries, as Cl-2 content increased, the etch rate continuously increased and the highest etch rates were obtained at 80% Cl-2 content. In the 40Cl(2)/10Ar and 40Cl(2)/10O(2) ICP discharges, the etch rate initially increased with increasing ICP source power up to 600 W and then decreased above 600 W, while the etch rate showed a strong dependence on the rf chuck power. The Cl-2/Ar ICP discharges produced significantly higher etch rates than the Cl-2/O-2 plasmas and maximum etch rates of similar to 97 nm/min and similar to 40 nm/min were obtained in the 40Cl(2)/10Ar and 40Cl(2)/10O(2) ICP discharges, respectively. Under all plasma compositions investigated, the surfaces etched in the Cl-2/Ar plasmas exhibited a constant normalized O/Ga ratio of similar to 0.85, which was somewhat lower than that of the unetched surface. The original stoichiometry was maintained on the Ga2O3 surfaces etched in the 40Cl(2)/10O(2) ICP discharges while a significant preferential desorption of oxygen atoms was observed for the Ga2O3 surfaces etched in the Cl-2/O-2 ICP discharges with Cl-2 content below 60%. Pattern transfer with better anisotropy was achieved with the Cl-2/Ar ICP discharges due to energetic Ar+ ion-assisted nature of the etching.

Keywords

(-201) beta-Ga2O3Inductively coupled plasma etchingCl-2/ArCl-2/O-2Near-surface stoichiometry

Identifiers

Scopus EID
2-s2.0-105021254879
WoS UID
001609722100001
KCI
ART003293881